Εμφάνιση ενός μόνο μηνύματος
  #19  
Παλιά 27-12-10, 05:45
Το avatar του χρήστη rapid_fast
rapid_fast Ο χρήστης rapid_fast δεν είναι συνδεδεμένος
Valvetronic soupa user
 
Εγγραφή: 15-05-2006
Μηνύματα: 7.731
rapid_fast has much to be proud ofrapid_fast has much to be proud ofrapid_fast has much to be proud ofrapid_fast has much to be proud ofrapid_fast has much to be proud ofrapid_fast has much to be proud ofrapid_fast has much to be proud ofrapid_fast has much to be proud ofrapid_fast has much to be proud ofrapid_fast has much to be proud of
Μου αρέσεις Ευάγγελε...
Διάβασε καλά, και βγάλε τα συμπεράσματα σου...

Bedding-in new pads and rotors should be done carefully and slowly. Rapid heat build up in the brake system can lead to warped rotors and or glazed brake pads. Most brake pad compounds will take up to 300-400 miles to fully develop an even transfer film on the rotors. Following are the recommended bed-in procedures from each manufacturer:

AKEBONO

400 to 500 miles of moderate driving is recommended. Consumer should avoid heavy braking during this period.

ATE

400 to 500 miles of moderate driving is recommended. Consumer should avoid heavy braking during this period.

BREMBO Gran Turismo

In a safe area, apply brakes moderately from 60mph to 30mph and then drive approximately 1/2 mile to allow the brakes to cool. Repeat this procedure approximately 30 times.

HAWK

After installing new pads make 6 to 10 stops from approximately 35 mph with moderate pressure. Make an additional two to three hard stops from approximately 40 to 45 mph. Do not allow the vehicle to come to a complete stop.When completed with this process, park the vehicle and allow the brakes to cool completely before driving on them again. Do not engage the parking brake until after this cooling process is compete.

NOTE: Hawk racing pads (Blue, Black, HT-10, HT-12) may require a different bed-in procedure. Contact your sales specialists at the Tire Rack for racing application information.

POWER SLOT

Follow the brake pad manufacturer's recommended break-in procedure taking care not to produce excessive heat in the system. Avoid heavy braking for the first 400-500 miles.

SATISFIED

For Gransport GS6 Carbon Ceramic Pads —

Step 1: Make 10 stops from 30 mph (50 kph) down to about 10 mph (15 kph) using moderate braking pressure and allowing approximately 30 seconds between stops for cooling. Do not drag your pads during these stops. After the 10th stop, allow 15 minutes for your braking system to cool down.

Step 2: Make 5 consecutive stops from 50 mph (80 kph) down to 10 mph (15 kph). After the 5th stop, allow your braking system to cool for approximately 30 minutes. This completes the break-in of your pads to the rotor surface.

During Steps 1 & 2, a de-gassing process occurs which may produce an odor coming from your pads as they complete the break-in cycle. This odor is normal and is part of the process your pads must go through to achieve their ultimate level of performance. The odor will go away after allowing your braking system to cool for approximately 30 minutes.

As with any new set of pads, do not tow a trailer or do any hauling during the break-in period.

Full seating of your new brake pads normally occurs within 1,000 miles.

For all other Satisfied pads —

400 to 500 miles of moderate driving is recommended. Consumer should avoid heavy braking during this period.
__________________
Τα "μαστόρια" χαλάνε τα αυτοκίνητα μας....
Απάντηση με παράθεση