GENERAL INFO ABOUT V32 SW 4-1/00
- SI B65 21 02
- Audio, Navigation, Monitors, Alarms, SRSJune 2008
- Technical Service
- This Service Information bulletin supersedes SI B65 21 02 dated March 2008.
- designates changes to this revision
- SUBJECT
- Navigation System Operating Software
- MODEL
- E38 (7 Series)
- E39 (5 Series)
- E46 (3 Series)
- E53 (X5)
- E83 (X3)
- E85, E86 (Z4)
- E65, E66 (7 Series)
- INFORMATION
- With the introduction of the navigation system operating software V32, there are currently 2 valid
- versions of navigation software:
- 1. Navigation system operating software V17.1 is used on MK III systems without the "split
- screen".
- 2. Navigation system operating software V32 is used on MK I, MK II, MK III navigation
- systems with split screen, DVD-Top navigation systems (MK IV) on I-Bus vehicles and
- NAVI01, NAVI02, NAVI03 on E65/E66 vehicles.
- CORRECTION
- Navigation system operating software should be updated under the following circumstances:
- • There are no corrections or new data for the US market included.
- • The navigation computer has been replaced.
- • Progman prompts the navigation software to be updated during programming/coding.
- • If instructed by a Service Information bulletin or the Regional Technical Engineer (RTE).
- CORRECTIONS INTRODUCED WITH PRIOR NAVIGATION SOFTWARE V31
- NAVI03 and DVD-Top NAV system-improved software for:
- • Reading dual layer DVDs
- • Loading voice files
- CORRECTIONS INTRODUCED WITH PRIOR NAVIGATION SOFTWARE V30
- • E65 and E66: Navigation system is inoperative after arrival at destination
- • E65 and E66: Incorrect address book
- NEW FEATURES INTRODUCED WITH NAVIGATION SOFTWARE V32
- No new features
- FEATURES INTRODUCED WITH PRIOR NAVIGATION SOFTWARE V31 AND V30
- No new features
- FEATURES INTRODUCED WITH PRIOR NAVIGATION SOFTWARE V29
- Destination input screen text changes:
- • "State/Province" instead of "Country"
- • "City/Postal Code" instead of "City/ZIP"
- • "Town/City" instead of "City" (only in conjunction with road maps before 2006-2)
- FEATURES INTRODUCED WITH PRIOR NAVIGATION SOFTWARE V28
- E83, E85, and E86 - software fix for the following display/flap issues:
- • Display turns back on after switching "Monitor off".
- • Flap opens/closes by itself.
- • Flap doesn't open.
- FEATURES INTRODUCED WITH PRIOR NAVIGATION SOFTWARE V27
- Only E46 (3 Series), E53 (X5), E83 (X3), E85 (Z4) with the DVD-Top navigation system:
- • Disclaimer screen disappears automatically after 8 seconds.
- • City/Town names displayed in the map.
- E46 (3 Series), E53 (X5), E83 (X3), E85 (Z4) with the DVD-Top navigation system;
- E65, E66 (7 Series) DVD NAVI03 (from 03/05):
- Destination input when "Country" (United States or Canada) is selected via:
- • ZIP code (only for the United States)
- • City name
- Destination input when a US state or a Canadian province is selected via:
- • Street name
- • City name
- • ZIP code (only for the United States)
- Note - Only in conjunction with NAVTEQ DVD road Map 2006-2 or a more recent version:
- • POI (Point of Interest) icons and "City center" icons are displayed together.
- • Travel Information (TMC) is no longer displayed (is inactive and not selectable).
- • Entries in "Address Book/Last Destination" displayed as:
- • City name, street name (destination entry via city name)
- • ZIP code, city name, street name (destination entry via ZIP code)
- • Product information
- • Legal disclaimer for usage of the navigation system and the data on the NAVTEQ road
- maps
- ------------------------------------------------------------------------------
- FEATURES INTRODUCED WITH PRIOR NAVIGATION SOFTWARE V26
- • The actual location is shown as an arrow in a circle.
- • The destination is marked with a checkered flag.
- • Map positioning in "travel direction" can now be selected in scales up to 100 mi.
- • Disabled POI icons are now selectable on I-Bus DVD NAV systems in:
- • General Destinations
- • Travel Information
- • The following functions are now selectable on the E65 and E66 with NAVI03 (from
- 03/2005):
- • Hide Map icons
- • General destinations and travel information
- After loading NAVI SW V32, the vehicle must be driven to ensure the proper functioning
- of the navigation system and the correct display of road number icons (e.g., interstate icons).
- CHECKING THE SOFTWARE VERSION
- MK I Systems
- The software version is shown in the top right corner of the "setting" screen. The software/hardware
- version is displayed as "1-1/80". The numbers have the following meanings: the first digit, 1, is a
- 1st generation navigation system (MK I); the second digit, 1, is a 1st device variant (top navigation
- – MK Ic color screen); the last two digits, 80, are the software version of the graphic component
- (8.0).
- MK II Systems
- The software version is shown in the top right corner of the "setting" screen. The software/hardware
- version is displayed as "2-1/81". The numbers have the following meanings: the first digit, 2, is a
- 2nd generation navigation system (MK II); the second digit, 1, is a 1st device variant (top
- navigation – MK IIc color screen); the last two digits, 81, are the software version of the graphic
- component (8.1).
- MK III Systems
- The software version is shown in the top right corner of the "setting" screen. The software/hardware
- version is displayed as "3-1/63" or "3-2/63" (MK III with split screen). The numbers have the
- following meanings: the first digit, 3, is a 3rd generation navigation system (MK III); the second
- digit, 1, is a 1st device variant (top navigation – MK IIIc color screen), or 2 is a 2nd device variant
- (radio navigation – MK IIIm monochrome display); the last two digits, 63, are the software version
- of the graphic component (6.3).
- DVD-Top navigation system for I-Bus vehicles
- The software version is shown in the top right corner of the "setting" screen. The software/hardware
- version is displayed as "4-1/00". The numbers have the following meanings: the first digit, 4, is a
- 4th generation navigation system (DVD); the second digit, 1, is a 1st device variant (top navigation
- – DVD color screen); the last two digits, 00, are the software version of the graphic component
- (10.0).
- E65 and E66 Systems
- • Enter the Service Mode of the Control Display.
- • Select "MOST Devices".
- • Scroll down and select "Navigation".
- • Scroll down a few pages until "Software Version" is displayed.
- • Software version for CD navigation (NAVI01) should be 7.3.2 (I-level E065-05-03-810.2).
- • Software version for DVD navigation (NAVI02) should be 8.4.4 (I-level E065-05-03-
- 800.2).
- • Software version for DVD navigation (NAVI03) should be E065-08-03-550 (SW
- 09.08.02).
- Current Software Versions
- Software version
- Application
- 8.0
- MK I - E39, E38 (up to 9/97)
- 8.1
- MK II - E39, E38 (from 9/97), E46, X5
- 9.0
- MK II - Radio Navigation – E52 (Z8)
- 5.1
- MK III Radio Navigation – E52 (Z8) from 09/00
- 3.1*
- MK III w/o Split Screen -E46 from 06/00, E39,E38 from 09/00, E53 from 10/00
- 6.3
- MK III with Split Screen
- 10.0
- DVD-Top Navigation
- 7.3.2
- E65, E66 NAVI01 (CD-drive)
- 8.4.4
- E65, E66 NAVI02 (DVD-drive)
- 09.08.02
- E65, E66 NAVI03 (DVD-drive)
- *Included in navigation software CD V17.1
- LOADING SOFTWARE (ALL EXCEPT THE E65 AND E66)
- For MK I, MK II, MK III, and DVD-Top NAV systems (except for the E65 and E66), use the
- following software loading instructions:
- 1. Turn the ignition to position 1 (terminal R).
- Do not cycle the key or perform diagnosis while installing the new software. Make sure that the
- power supply is stable, i.e., do not switch on any electrical loads.
- 1. Activate "GPS-Navigation" and acknowledge the screen disclaimer by pushing the rotary
- knob on the board monitor.
- 2. Remove the map CD from the navigation computer by pressing the "Eject" button.
- 3. Insert the navigation software CD (V17.1 P/N 01 59 9 789 299 index "x" for Mk III
- without the split screen; V32 P/N 01 59 0 141 891 index "y" for all other versions).
- 4. Mark I System (up to 9/97 production):
- After a few seconds, the BMW roundel will appear on the board monitor and will be "filled in"
- clockwise to show the progress of loading (approx. 4-6 minutes).
- Mark II System (from 9/97 production)
- Mark III System (E46 from 06/00 and E38, E39, and E52 from 09/00 production)
- DVD-Top navigation system (E46, E39, E52 from 09/02 and E53, E85 from 10/02 production):
- After a few seconds, a menu of notes on the loading procedure and the "Progress" bar appear on the
- board monitor.
- When the loading process has been completed, the message "Software has been successfully
- loaded" is displayed.
- 1. Remove the navigation system operating software CD and confirm the end of the loading
- process by pressing the rotary knob on the board monitor. "OK" appears in the display.
- 2. Drive the vehicle before delivering it to the customer to ensure that the navigation system is
- functioning and displaying (interstate icons) correctly.
- LOADING SOFTWARE (E65 AND E66 ONLY)
- When programming any E65 or E66 using Progman V27.0 or higher, you will be prompted by
- the Progman screen that the "BMW navigation CD" must be loaded prior to programming the
- vehicle.
- Note: Connect an approved battery charger before loading the software.
- 1. Turn the ignition on to Terminal R or 15.
- 2. Enter the navigation menu.
- 3. Remove the NAVTEQ road map CD/DVD.
- 4. Insert the navigation operating software CD V32 (P/N 01 59 0 141 891 index "y") into
- the navigation computer and use the latest Progman version for NAVI03 (DVD navigation).
- 5. Select "Yes" with the controller to install the software.
- 6. The software will then load in two steps, taking approximately 10-15 minutes.
- 7. Do not touch the iDrive while the software is loading.
- 8. When the installation is finished, the CD will be ejected. The message "Installation
- Successful, Remove Software loading CD and press OK" will appear. At this point, select
- "OK" with the controller.
- 9. The navigation system will then "Reinitialize".
- 10.When prompted, insert the NAVTEQ road map CD/DVD.
- 11.Refer to SI B09 05 01 (Coding, Individualization and Programming) for any necessary
- coding and programming. Note that Progman will automatically reprogram all
- programmable control units that do not have the latest software.
- 12.Drive the vehicle before delivering it to the customer to ensure that the navigation system
- is functioning and displaying (interstate icons) correctly.
- NAVIGATION COMPUTER REPLACEMENT - MK III AND DVD NAV
- When replacing a defective MK III or DVD NAV computer, a configuration signal is required
- to allow the new computer to load the correct software for its respective application. This is
- generated by using the SSS (Software Service Station) loaded with the latest Progman version, and
- the navigation system operating software CD V17.1 or V32.
- 1. Connect the Deutronic battery charger to the vehicle.
- 2. Connect the SSS via a diagnostic head or an O(P)PS (for D-CAN vehicles) to the vehicle.
- 3. Open a "New session" in Progman; select "Load SW" and follow the on-screen messages.
- 4. Select "Retrofits".
- 5. Select "Languages".
- 6. First select "Display" to select and/or check the correct languages.
- 7. Then select "Navigation" to select the languages for the NAV system.
- 8. At the prompt "Is the CD-ROM present?" select "Yes", but do not insert the navigation
- CD into the Nav Computer yet!
- 9. First select the main language and then an additional language (the choices are English,
- French, Italian, Spanish, and German).
- 10.NOTE: The gender of the announcer's voice (male or female) can no longer be selected.
- • MK I, MK II & MK III: Only male.
- 11.DVD-Top NAV, NAVI01, NAVI02 and NAVI03: Only female.
- 12.After activation of the automatic coding, the DIS tester tells you to follow the instructions
- on the monitor for navigation CD installation.
- 13.Place the navigation CD into the navigation computer CD drive.
- Important: Do not switch the ignition OFF during the software loading procedure.
- 1. Once the loading has been completed, remove the CD and then confirm completion by
- pressing the rotary push button on the monitor.
- 2. Turn the ignition OFF for 10 seconds, and then turn it ON and conduct a functional check.
- 3. After this step has been finished, encode the navigation computer in the regular manner,
- using the path "1 Recoding".
- TROUBLESHOOTING HINTS
- The following problems may occur during the software loading procedure:
- • The message "CD defective" appears on the display screen.
- • The message "Fault during programming" appears on the display screen.
- • The message "The system is restarting" appears on the display screen.
- • The installation process has stopped; the display screen is blank; and the power LED on the
- navigation computer is off. The CD will not eject.
- These complaints are usually the result of a faulty navigation operating software CD.
- • For points 1-3 (error messages that appear on the display screen), check for the correct
- software version and try loading a new navigation CD.
- • For a CD that will not eject from the navigation computer, follow the procedure below:
- 1. Remove the navigation computer.
- • Unplug the voltage supply (blue connector).
- • Reconnect the voltage supply, and immediately press the eject button repeatedly until the
- CD in the drive is ejected.
- • Insert a new navigation software CD and restart the installation process.
- PARTS INFORMATION
- Part Number
- Description
- 01 59 9 789 299
- Navigation Software CD V17.1 Index "x"
- 01 59 0 141 891
- Navigation Software CD V32 Index "y"
- --------------------------------------------------------------------------------------
- WARRANTY INFORMATION
- Updating the vehicle at the customer's request is not covered under warranty.
Τελευταία επεξεργασία από το χρήστη snoopjohn : 13-10-08 στις 17:43
|